Philips LX3600 speelt geen DVD'S

[phil 3548]

 

 

@All

 

Ik heb hier een Philips LX3600 van een collega staan.De speler heeft problemen met het afspelen van DVD-schijfjes. Soms speelt het apparaat eventjes probleemloos om vervolgens te stoppen met de mededeling no disc.

CD-schijfjes geven geen problemen.

 

Wie weet raad?

 

Phil

[topie]

Kan een defecte laser zijn of een software fout.

[percies]

Brobeer inderdaad eerst nieuwe software

 

 

 

A. Preparation to upgrade the firmware:

1. Unzip lx3600d_v29.zip ( see file attached ).

2. Start the CD Burning software and create a new CD project (data

disc) with the following settings:

File system : ISO9660

Format : Mode1, CD-ROM

Recording mode : Single Session (Track-At-Once), Finalized CD

3. Place the content of the zip-archive (1 file) into the root directory of

the new CD project.

4. Burn the data onto a blank CDR.

Note: ISO9660 is mandatory, UDF discs are not supported !

The final CDROM must not contain any other data except the file

from the zip-archive.

B. Procedure to apply the firmware upgrade:

1. Power up the set and open tray.

2. Insert the prepared Upgrade CDROM and close the tray.

3. The set will response and display the following messages:

" LOAD [after the disc is read the tray will open to remove the disc]

" ERASE 0 -> ERASE F ..... -> ERASE 0

" WRITE F ..... -> WRITE 0

" UPG END [displayed only for a short moment, if unsuccessful

ERROR is shown]

" DISC

" LOAD [tray will close indicating that the upgrade process is

completed]

4. Unplug the set to disconnect the mains supply.

5. The whole process should last for about 5 minutes.

C. Reprogramming the DVD version Matrix

1. Put the set in Stop mode with tray open

2. Press buttons -9- -9- -9- -9- -AUDIO- -a- on the Remote

Control, where a is as given below:

1 = /22 & /25 Europe 2 = /93 China

3 = /69 Asia Pacific 4 = /75 Australia/New Zealand

5 = IK India Kit 6 = /78 Latam

7 = LK Brazil Kit 9 = /17 USA

D. How to read out the firmware versions to confirm upgrading

1. Power up the set and open tray in DVD mode.

2. Press -OSD- on the Remote control.

3. The TV screen will show:

SERVO: servo version no REG: region number

Model - software date in yymmdd - V version no stroke

version

841810-lx3600d_v29.zip

[phil 3548]

@fransv

 

Ik zal je suggestie van het weekend even proberen.

Alvast hartelijk dank voor het meedenken.

 

Phil

[GreenPolo]

@ fransv

 

Waar heb je deze software vandaan? Ik heb ongeveer dezelfde

problemen met een LX 3000.

Zou je mij de link kunnen geven? ( evt via PM)

[percies]

Voor de LX3000 !!!!!!!

 

The upgrade addresses the following issue:

- Sound is muted during tracknumber increase on CDs with live music

content or on CDs recorded in disc-at-once mode.

--------------------------------------------------------------------------------------------------

All older sets brought in for repair should be upgraded as preventive action.

--------------------------------------------------------------------------------------------------

A. Preparation to upgrade software:

1. Unzip the zip-archive attached to this Service Newsletter

2. Start the CD Burning software and create a new CD project (data

Disc) with the following settings:

File system: ISO9660, JOLIET

Format: MODE 1: CDROM

Recording mode: SINGLE SESSION (TRACK-AT-ONCE),

FINALIZED CD

3. Place the content of the zip-archive (1 file) into the root directory of

the new CD project.

4. Burn the data onto a blank CDR

 

Note: ISO9660 is mandatory, UDF discs are not supported !

The final CDROM must not contain any other data except the file

from the zip-archive.

 

B. Procedure to apply the software upgrade:

1. Power up the set and open the DVD tray.

2. Insert the prepared Upgrade CDROM and close the tray.

3. The TV screen will show the following messages in sequence:

disc loading ® bank30.rom ® writing ® done

4. The whole process takes less than 10 seconds after which the set

shuts down and the TV screen becomes dark.

Note: Do not press any buttons or interrupt the mains supply during

the entire upgrading process, otherwise the set may become

defective.

5. Unplug & replug the mains cable

6. Open the DVD tray and remove Upgrade CDROM.

7. Reset the system by using the Remote control, select

System Menu ® Feature setup ® Default ® Reset

 

C. How to read out the software versions to confirm upgrading

1. Open the DVD tray

2. Press <123> on the Remote control.

3. The software version VER 0517 1 xx y is displayed on the TV

screen. The region code (digit y) should remain as before

upgrading, otherwise restore the region code as descibed in the

Service Manual on page 2-1.

D. Before returning the set to customer

1. Check & ensure that the TV system and Video out are setup as in

the table below ( snl2003-03-10.jpg).

 

REMARKS :

Zip-archive file lx3000d_v0517_1.zip is for LX2000D and LX3000D

family except /35S

842443-lx3000d_ver_0517_1.zip

[GreenPolo]

Ik ga er mee aan de slag, bedankt <img src="/ubbthreads/images/graemlins/xyxthumbs.gif" alt="" />

[Gast]

Bij mij is het precies andersom. Hij speelt wel DVD's maar geen CD's?????